Peugeot 309 MOT Results
Registered in 199061.8% pass rate
from 55 tests in 2021
More MoT Results
Failure rates by item
Here you can drill down into the failure rates for each item on the test. We've also compared the rates to the average results for 1990 cars and highlighted areas where the Peugeot 309 is unusually good or bad.
-
20% fail on
Brakes
-
16% fail on
Brake performance
(130% worse than other 1990 cars)
-
9.1% fail on
Service brake performance
(2 times worse than other 1990 cars)
-
9.1% fail on
Rbt
(2 times worse than other 1990 cars)
- 7.3% fail on Service brake performance
- 1.8% fail on Service brake imbalance
-
9.1% fail on
Rbt
(2 times worse than other 1990 cars)
-
7.3% fail on
Service Brake Efficiency (sp)
-
7.3% fail on
Rbt (sp)
- 7.3% fail on Service brake imbalance
- 1.8% fail on Service brake performance
-
7.3% fail on
Rbt (sp)
- 1.8% fail on Brake performance not tested
-
1.8% fail on
Parking brake efficiency (sp)
- 1.8% fail on Rbt (sp)
-
9.1% fail on
Service brake performance
(2 times worse than other 1990 cars)
-
5.5% fail on
Mechanical brake components
(4 times worse than other 1990 cars)
-
1.8% fail on
Brake linings and pads
- 1.8% fail on Brake linings
-
1.8% fail on
Brake discs and drums
- 1.8% fail on Brake discs
-
1.8% fail on
Brake cables, rods, levers and linkages
- 1.8% fail on Cable
-
1.8% fail on
Brake linings and pads
-
1.8% fail on
Parking brake control
- 1.8% fail on Lever
- 1.8% fail on Rigid brake pipes
- 1.8% fail on Flexible brake hoses
-
1.8% fail on
Brake actuators (including spring brakes or hydraulic cylinders)
- 1.8% fail on Hydraulic brake cylinder
-
16% fail on
Brake performance
(130% worse than other 1990 cars)
-
15% fail on
Suspension
- 7.3% fail on Component mounting prescribed areas
-
3.6% fail on
Suspension arms
- 1.8% fail on Ball joint
- 1.8% fail on Ball joint dust cover
-
3.6% fail on
Sub-frames
(5 times worse than other 1990 cars)
- 1.8% fail on Sub-frame
- 1.8% fail on Pins and bushes
- 1.8% fail on Wheel bearings
-
1.8% fail on
Anti-roll bars
- 1.8% fail on Linkage ball joints
-
13% fail on
Lamps, reflectors and electrical equipment
-
7.3% fail on
Headlamps
- 5.5% fail on Headlamp
- 1.8% fail on Dipswitch
- 1.8% fail on Stop lamp
-
1.8% fail on
Direction indicators
-
1.8% fail on
Flashing type
- 1.8% fail on Side repeaters
-
1.8% fail on
Flashing type
- 1.8% fail on Registration plate lamp(s)
-
1.8% fail on
Electrical equipment
- 1.8% fail on Horn
-
7.3% fail on
Headlamps
-
9.1% fail on
Body, chassis, structure
- 5.5% fail on Exhaust system
-
3.6% fail on
Transmission
-
3.6% fail on
Drive shafts
- 3.6% fail on Joints
-
3.6% fail on
Drive shafts
-
1.8% fail on
Chassis
- 1.8% fail on Chassis condition
-
9.1% fail on
Noise, emissions and leaks
-
7.3% fail on
Exhaust emissions
-
5.5% fail on
Spark ignition
- 3.6% fail on Non catalyst emissions
- 1.8% fail on Emissions not tested
-
1.8% fail on
Compression ignition
- 1.8% fail on Emissions not tested
-
5.5% fail on
Spark ignition
-
1.8% fail on
Fluid leaks
- 1.8% fail on Engine oil leaks
-
7.3% fail on
Exhaust emissions
-
5.5% fail on
Seat belts and supplementary restraint systems
-
5.5% fail on
Seat belts
- 3.6% fail on Prescribed areas
- 1.8% fail on Condition
-
5.5% fail on
Seat belts
-
1.8% fail on
Steering
-
1.8% fail on
Steering gear
- 1.8% fail on Steering rack
-
1.8% fail on
Steering gear
-
1.8% fail on
Visibility
- 1.8% fail on Washers
-
1.8% fail on
Road Wheels
- 1.8% fail on Attachment
-
1.8% fail on
Tyres
- 1.8% fail on Condition